 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| lite-on technology corporation property of lite-on only piranha leds LTL912CBKS5 selection guide part no. color v (lm) va(deg.) d(nm) LTL912CBKS5 blue 0.8 45 470 benefits z fewer leds required z lower lighting system cost applications z automotive lighting z signs and signals z room lighting part no. : LTL912CBKS5 page 1 of 12 bns-od-c131/a4 pb free
lite-on technology corporation property of lite-on only features z high current operation z high flux output z low thermal resistance z low profile z wide viewing angle z meet sae/ ece/ jis automotive color requirement z tube package for automatic loading and insertion process description these parts are designed for high current operat ion and high flux output applications. in order to solve the high temperature produced by the higher current operation, the package?s design features better thermal management charac teristics than other led solutions coupled with an efficient optical design. this package design allows the lighting designer to reduce the number of leds required as well as the overall lighting system cost. t he low profile package can be easily coupled to reflectors or lenses to efficiently distri bute light and provide the desired illuminated appearance. this product family employs the world?s bright est red, red-orange, amber, blue, cyan, green, and white led materials etc., which allow desi gners to match the color of popular lighting applications, such as automotive lighting and electronic signs. devices lens source part no (ltl*) color diffusion dice source color LTL912CBKS5 water clear non-diffused ingan blue part no. : LTL912CBKS5 page 2 of 12 bns-od-c131/a4 lite-on technology corporation property of lite-on only package dimensions notes: 1. all dimensions are in millimeters (inches). 2. protruded resin is 1.0mm(.04") max. 3. lead spacing is measured where the leads emerge from the package. 4. specifications are subject change to without notice. part no. : LTL912CBKS5 page 3 of 12 bns-od-c131/a4 lite-on technology corporation property of lite-on only absolute maximum ratings at ta=25 parameter ingan unit power dissipation 225 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 100 ma continuous forward current 50 ma reverse voltage (i r =100 a) 5 v operating temperature range -40 to + 100 storage temperature range -55 to + 100 led junction temperature 125 soldering preheat temperature 100 for 30 seconds lead soldering temperature 260 for 5 seconds [1.5mm (.06?) from seating plane] notes: 1. operation at currents below 10ma is not recommended. part no. : LTL912CBKS5 page 4 of 12 bns-od-c131/a4 lite-on technology corporation property of lite-on only electrical / optical characteristics at t a =25 parameter symbol part no. min. typ. max. unit test condition total flux lite-on technology corporation property of lite-on only typical electrical / optical characteristics curves (25 ambient temperature unless otherwise noted) 0.0 0.2 0.4 0.6 0.8 1.0 1.2 400 420 440 460 480 500 520 540 wavelength (nm) relative intensity fig. 1 relative intensity vs wavelength 0 20 40 60 2.533.544.5 forword voltage vf (v) forward current if (ma) fig. 2 forward current vs forward voltage 0 10 20 30 40 50 60 0 102030405060708090100 t ambient () forward current i f (ma ) fig. 3 forward current vs ambient temperature 0 0.2 0.4 0.6 0.8 1 1.2 0 102030405060 forwrad current if (ma) relative luminous intensity fig. 4 relative intensity vs forward current 0 0.2 0.4 0.6 0.8 1 1.2 -80 -60 -40 -20 0 20 40 60 80 viewing angule (deg.) relative luminous intensity fig. 5 relative intensity vs off axis angle part no. : LTL912CBKS5 page 6 of 12 bns-od-c131/a4 lite-on technology corporation property of lite-on only bin code list for reference part no. : LTL912CBKS5 page 7 of 12 bns-od-c131/a4 bin code minimum maximum 3y 0.25 0.55 3z 0.4 0.8 a 0.6 1.2 b 1.0 1.8 c 1.5 1.8 luminous flux (light-output; lm) @i f =50ma, t a =25 3z 8 b3 category code bin code minimum maximum 3 3.60 4.00 4 3.80 4.20 5 4.00 4.40 6 4.20 4.60 7 4.40 4.80 8 4.60 5.00 9 4.80 5.20 forward voltage (volt) @i f =50ma, t a =25 bin code minimum maximum b2 459 466 b3 464 471 b4 469 476 hue (nm) @i f =50ma, t a =25 lite-on technology corporation property of lite-on only packing spec 1. tube: 65pcs dim: 520mm x 9.6mm x 11.8mm 2. inner carton: 187 tubes x 65 pcs = 12,155 pcs dim: 530mm x 175mm x 128mm 3. outer carton: 4 inner cartons x 12,155 pcs = 48,620 pcs dim: 545mm x 370mm x 280mm part no. : LTL912CBKS5 page 8 of 12 bns-od-c131/a4 lite-on technology corporation property of lite-on only cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).c onsult liteon?s sales in advance for information on applications in which exceptional relia bility is required, particularly when the failure or malfunction of the leds may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their origin al packaging are used within three months. for extended storage out of their original packagi ng, it is recommended that the leds be stored in a sealed container with appropriate desiccan t or in desiccators with nitrogen ambient. 3. cleaning use alcohol-based cleaning solvents such as is opropyl alcohol to clean the leds if necessary. 4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must be done before soldering, at normal temperature. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 5. soldering when soldering, leave a minimum of 2mm clearance from the b ase of the lens to the soldering point. dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame dur ing soldering while the led is at high temperature. recommended soldering conditions : soldering iron wave soldering temperature soldering time 300c max. 3 sec. max. (one time only) pre-heat pre-heat time solder wave soldering time 100c max. 60 sec. max. 260c max. 5 sec. max. note: excessive soldering temperature and/or time might result in deformation of the led lens or catastrophic failure of the led. ir re-flow is not suitable process for through whole type piranha led production. part no. : LTL912CBKS5 page 9 of 12 bns-od-c131/a4 lite-on technology corporation property of lite-on only the suggesting soldering conditions are listed in table whic h is on page 9. the wave solder temperature profile which is showed as below figure is taken on the bottom side of the pcb board. both of the suggesting and maximum conditions are all shown in the figure as below. part no. : LTL912CBKS5 page : 10 of 12 bns-od-c131/a4 preheat 30 5sec (time max =60sec) 85 15 (temp max =100 ) peak 2.5sec (time max =5sec) 235 (temp max =260 ) wave solder temperature profile 0 40 80 120 160 200 240 280 0 8 16 24 32 40 48 56 64 time (sec) temperature ( o c) lite-on technology corporation property of lite-on only 6. drive method an led is a current-operated device. in orde r to ensure intensity uniformity on multiple leds connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in seri es with each led as shown in circuit a below. circuit model a circuit model b led led (a) recommended circuit (b) the brightness of each led might appear different due to the differences in the i-v characteristics of those leds 7. esd (electrostatic discharge) static electricity or power surge will damage the led. suggestions to prevent esd damage: ? use a conductive wrist band or anti- electrostatic glove when handling these leds ? all devices, equipment, and machinery must be properly grounded ? work tables, storage racks, etc. should be properly grounded ? use ion blower to neutralize the static charge which might have built up on surface of the leds plastic lens as a result of friction between leds during storage and handing esd-damaged leeds will exhibit abnormal character istics such as high reverse leakage current, low forward voltage, or ?no light up? at low currents. to verify for esd damage, check for ?light up? and vf of the suspect leds at low currents. the vf of ?good? leds should be >2.0v@0.1ma for ingan product and >1.4v@0.1ma for alingap product. part no. : LTL912CBKS5 page 11 of 12 bns-od-c131/a4 lite-on technology corporation property of lite-on only suggested checking list : training and certification 1. everyone working in a static-safe area is esd-certified? 2. training records kept and re-certification dates monitored? static-safe workstation & work areas 1. static-safe workstation or work-areas have esd signs? 2. all surfaces and objects at all static-safe workstation and within 1 ft measure less than 100v? 3. all ionizer activated, positioned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors) handling esd sens itive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. if conductive footwear used, conductive floor ing also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive s hoes checked daily and resu lt recorded for all dsl? 5. all wrist strap or heel strap checkers calibration up to date? note: *50v for blue led. device handling 1. every esds items identified by eia-471 labels on item or packaging? 2. all esds items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. no static charge generators (e.g. plasti cs) inside shielding containers with esds items? 4. all flexible conductive and dissipative packag e materials inspected before reuse or recycle? others 1. audit result reported to entity esd control coordinator? 2. corrective action from previous audits completed? 3. are audit records complete and on file? 8. others the appearance and specifications of the product may be modified for improvement, without prior notice. liteon may make process or materials changes affecting the performance or other characteristics of our products. these products supplied after such changes will continue to meet published specifications, but may not be identical to products supplied as samples or under prior orders. part no. : LTL912CBKS5 page 12 of 12 bns-od-c131/a4 |
Price & Availability of LTL912CBKS5
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |